Exactly how to Install a Tub (Step By Step).
Exactly how to Install a Tub (Step By Step).
Blog Article
They are making a few good annotation about Tools You Need to Install a New Bathtub overall in this post beneath.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is readily obtainable, the job can move easily; if you have to open up a wall to get rid of the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require a helper to move out the old bathtub and also embeded in the brand-new one. Ensure you have actually certified yourself for the job and fit trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is better to take into consideration utilizing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly help you install a brand-new bathtub in your bathroom if you have actually already acquired a new tub and also don't require to alter the arrangement of your previous water supply pipes.
Your tools and also material checklist must comprise the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite bothersome due to the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water supply and examine all joints and also new pipework for leaks and also tighten them if needed. Fill up the bathtub and additionally examine the overflow outlet and the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized a minimum of when as this will certainly settle it right into its final placement.
Planning for the Installation
To start with, the sustaining frame provided with the bath needs to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last position.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, resulting in issues with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog posting on A Step-by-Step Guide to Installing a Bathtub while surfing the web. Sharing is caring. Helping people is fun. Thank-you for going through it.
Schedule Now! Report this page